Difference between revisions of "Dragon 32 - CPU and PSU Modifcations and Compatibility"

From The Dragon Archive
Line 1: Line 1:
Section 1 - Brief description on Modifications and Compatibility for MK1 and MK3 PSU
+
Since the introduction of the Dragon 32 there have been several versions produced of both the Central Processing Unit (CPU_ and the Power Supply Unit (PSU).
Section 2 - More detailed information on Modifications and Compatibility for MK3 PSU
 
  
 +
Now all versions of the CPU  will work with the MK3 PSU; this service sheet identifies which  modifications are necessary to implement this.
  
== Section 1 ==
+
'''CPU TYPES'''
 +
16x16
 +
OKI
 +
PIGGY BACK
 +
SIEMENS
  
'''REPLACEMENT OF POWER SUPPLY AND CENTRAL PROCESSING UNITS ON THE DRAGON 32'''
+
'''PSU TYPES'''
 +
MK1 - 1286 Modulator
 +
MK2 - 1233 Modulator
 +
MK3 - 1287 Modulator
  
Since the introduction of the Dragon 32 there have been several versions produced of both the Central Processing Unit (CPU_ and the Power Supply Unit (PSU).
+
'''PSU COMPATABILITY'''
 +
MK1 PSUs now no longer manufactured.
 +
MK2 PSUs are obsolete and when encountered should always be replaced with MK3 boards.
 +
MK3 PSUs now used for all CPUs.
  
Most versions of the CPU and PSU will work together and this service sheet identified which combinations will, and the modifications necesarry to implement each of them.
+
'''NOTE:'''
 +
For PAL B computers use a normal 16x16 CPU with a MK3 PSU, the PSU only needs the sound altered from PAL A reception. This is done when PSU is checked and setup at PSU work station.
  
  
 +
== MK3 PSU with 16x16 CPU ==
  
'''Identification of boards'''
 
  
The first setp when replacing either unit with one of a different version is to identify the version of each of the boards you wish to use.
+
With the 16x16 CPU all mods (except possible add on capacitor to position C58) are completed at time of manufacture. Mods as listed below:-
  
PSU's can be identified by the type of modulator used. The model number being clearly marked on the top as follows:
+
CPU:
 +
    15K resistor (Brown, Green and Orange) to plate through hole which leads to IC12 PIN 10 (Sony Mod.) or for neatness resistor mat be fitted from C28 negative side to solder plate on IC12 Pin 10 line.
 +
    6.8K resistor (Blue, Grey and Red) from solder pad near C6 to bottom of R6.
 +
    If background lines are prominent, fit 220N capacitor in C58 position (Not done at time of manufacture).
 +
    220R resistor short circuited across R9 (R9 being 270R). Alternatively replace R9 with 120R.
  
{|{{Prettytable|width: 700px; font-size: 2em;}}
+
PSU:
|''PSU''||''Modulator Model Number''
+
    Remove existing 1.2K resistor in position R1 and replace with 330R resistor.
|-
+
    Remove existing 120K resistor in position R6 and replace with 22K resistor.
||MK1||1286
+
    Retune modulator sound core.
|-
 
|MK2||1233
 
|-
 
|MK3||1287
 
|-
 
|}
 
  
CPU's can be identified by comparing the RAM area with the descriptions below:
 
  
16x16      - Two rows of RAM chips, 1x9 and 1x7
+
== MK3 PSU and OKI CPU ==
Piggy Back - 6 chips on main board, piggy back board in sockets 1 and 8, 11 chips on piggy back board
 
Siemens    - 1 row of 16 RAM chips, 2 chips per socket (one chip on top of another)
 
OKI        - 8 RAM chips (usually labelled OKI)
 
  
  
Next from the table below, check that the combination you have chosen is a usable one.
+
CPU:
 
+
     15K resistor (Brown, Green and Orange) from Pin 4 IC10 to Pin 10 IC12 (Sony Mod.)
{|{{Prettytable|width: 700px; font-size: 2em;}}
+
     220N capacitor in position C21.
|''PSU''||''PIGGY BACK CPU''||''OKI CPU''||''SIEMENS CPU''||''16x16 CPU''
+
     Cut resistor R6 and solder single cone wire to cut end, then solder other end of wire to pin 14 IC11.
|-
+
    150 OHM resistor (Brownm Green and Brown) short circuited over R9.
|MK1||yes||yes||yes||yes
+
     Drill back of board to open circuit track.
|-
 
|MK2||no||no||no||no
 
|-
 
|MK3||yes||yes||yes||yes
 
|-
 
|}
 
 
 
*NOTE: MK2 PSU's are obsolete and when encountered should always be replaced with MK1 or MK3 boards.
 
 
 
 
 
 
 
 
 
'''MODIFICATIONS'''
 
 
 
Having selected a useable combination carry out the appropriate modifications from the following:-
 
 
 
'''MK1 PSU and Piggy Back or OKI CPU'''
 
 
 
CPU:  
 
     270R resistor in series with cassette input, i.e. the connection to Pin 4 of PL4
 
    *Sony Mod.
 
 
 
PSU:
 
     10R resistor in series with +5v feed to modulator.
 
 
 
 
 
'''MK3 PSU and Piggy Back or OKI CPU'''
 
 
 
CPU:
 
    150R resistor short circuit over R9.
 
     Cut resistor R6 (C49 side) and solder single cone wire to cut end, then solder other end of wire to Pin 14 IC11
 
     Drill back of board to open circuit track, i.e. between IC11 Pin 13 and cut end of R6.
 
    *Sony Mod.
 
 
 
PSU:
 
    Remove R1. This will either be a 1.2K or 68R resistor. For the 68R resistor, this was a modification and may be found on the back of the board and linked to R7; Replace 330R resistor in original R1 position.
 
  
 +
PSU:
 +
    Remove existing 1.2K resistor in position R1 and replace with 330R resistor.
 +
    Remove existing 120K resistor in position R6 and replace with 22K resistor.
 +
    Retune modulator sound core.
  
'''MK1 PSU and 16x16 CPU'''
 
  
CPU:
 
    1K resistor across PL6 Pin 9 and 0v. If background lines are prominent, fit 0.22uf capacitor in C58 position.
 
    *Sony Mod.
 
  
PSU:
+
== MK3 PSU and PIGGY BACK CPU ==
    10R resistor in series with +5v supply to modulator.
 
  
  
'''MK3 PSU and 16x16 CPU'''
+
CPU:
 +
    15K resistor (Brown, Green and Orange) from Pin 4 IC10 to Pin 10 IC12 (Sony Mod.)
 +
    220N capacitor in position C3
 +
    Cut resistor R6 and solder single cone wire to cut end, then solder other end of wire to pin 14 IC11.
 +
    150 OHM resistor (Brownm Green and Brown) short circuited over R9.
 +
    Drill back of board to open circuit track.
  
NOTE: With the 16x16 CPU, all mods (except possible add on capacitor to C58 position) are completed at time of manufacture, howvever some boards may still be present without mods. Mods as listed below:-
+
PSU:
 
 
CPU:
 
    6.8K resistor from sholder pad near C6 to bottom of R6 (C49 side).
 
    220R resistor short circuited across R9 (R9 being 270R). Alternatively replace R9 with 120R.
 
    If background lines are prominent, fit 220N capacitor in C58 position.
 
    *Sony Mod.
 
 
 
PSU:  
 
 
     Remove existing 1.2K resistor in position R1 and replace with 330R resistor.
 
     Remove existing 1.2K resistor in position R1 and replace with 330R resistor.
     Remove existing 120K resistor in position R6 and replace with 22K resistor. Retune modulator sound core.
+
     Remove existing 120K resistor in position R6 and replace with 22K resistor.
 
+
    Retune modulator sound core.
 
+
 
'''MK1 PSU and Siemens CPU'''
 
 
 
CPU:
 
    Change C7 to a 2.2-22pf trimmer. Place a 1K resistor between 0v and PL6 Pin 9.
 
 
 
PSU:
 
    10R resistor in series with +5v supply to modulator.
 
    *Sony Mod.
 
  
  
'''MK3 PSU and Siemens CPU'''
+
== MK3 PSU and SIEMENS CPU ==
 
 
CPU:
 
    6.8K resistor from bottom of R6 to solder plate near positive side of C28, 200R resistor short circuited over R9.
 
    C7 change to 2.2-22pf trimmer.
 
    1K resistor between 0v and PL6 Pin 9.
 
    *Sony Mod.
 
 
 
PSU:
 
    Remove existing 1.2K resistor in position R1 and replace with 330R resistor.
 
    Remove existing 120K resistor in position R6 and replace with 22K resistor. Retune modular sound core.
 
 
 
  
'''*Sony Mod'''
 
  
This modification was originally introduced to overcome loss of colour band problems encountered when the computer was used with Sony 22" televisions. It has been found however, that it also cures other colour problems and for that reason it is now considered standard on all CPUs.
+
CPU:
 +
    15K resistor (Brown, Green and Orange) from Pin 4 IC10 to IC12 PIN 10 (Sony Mod.) or for neatness resistor may be fitted from C28 negative side to solder plate on IC12 Pin 10 line.
 +
    220 OHM resistor short circuited over R9.
 +
    6.8K resistor (Blue, Grey and Red) from bottom of R6 to solder plate near positive side of C28. This resistor needs to be sleeved.
  
The modification is carried out by fitting 1 15K resistor across IC10 Pin 4 and IC12 Pin 10, or for neatness on the 16x16 and Siemens board the resistor may be fitted from C28 negative side to a solder plate on IC12 pin 10 line.
+
PSU:
 +
    Remove existing 1.2K or 68R resistor in position R1 and replace with 330R resistor.
 +
    Remove existing 120K resistor in position R6 and replace with 22K resistor.
 +
    Retune modulator sound core.

Revision as of 22:13, 18 March 2009

Since the introduction of the Dragon 32 there have been several versions produced of both the Central Processing Unit (CPU_ and the Power Supply Unit (PSU).

Now all versions of the CPU will work with the MK3 PSU; this service sheet identifies which modifications are necessary to implement this.

CPU TYPES 16x16 OKI PIGGY BACK SIEMENS

PSU TYPES MK1 - 1286 Modulator MK2 - 1233 Modulator MK3 - 1287 Modulator

PSU COMPATABILITY MK1 PSUs now no longer manufactured. MK2 PSUs are obsolete and when encountered should always be replaced with MK3 boards. MK3 PSUs now used for all CPUs.

NOTE: For PAL B computers use a normal 16x16 CPU with a MK3 PSU, the PSU only needs the sound altered from PAL A reception. This is done when PSU is checked and setup at PSU work station.


MK3 PSU with 16x16 CPU

With the 16x16 CPU all mods (except possible add on capacitor to position C58) are completed at time of manufacture. Mods as listed below:-

CPU:

    15K resistor (Brown, Green and Orange) to plate through hole which leads to IC12 PIN 10 (Sony Mod.) or for neatness resistor mat be fitted from C28 negative side to solder plate on IC12 Pin 10 line.
    6.8K resistor (Blue, Grey and Red) from solder pad near C6 to bottom of R6.
    If background lines are prominent, fit 220N capacitor in C58 position (Not done at time of manufacture).
    220R resistor short circuited across R9 (R9 being 270R). Alternatively replace R9 with 120R.

PSU:

    Remove existing 1.2K resistor in position R1 and replace with 330R resistor.
    Remove existing 120K resistor in position R6 and replace with 22K resistor.
    Retune modulator sound core.


MK3 PSU and OKI CPU

CPU:

    15K resistor (Brown, Green and Orange) from Pin 4 IC10 to Pin 10 IC12 (Sony Mod.)
    220N capacitor in position C21.
    Cut resistor R6 and solder single cone wire to cut end, then solder other end of wire to pin 14 IC11.
    150 OHM resistor (Brownm Green and Brown) short circuited over R9.
    Drill back of board to open circuit track.

PSU:

    Remove existing 1.2K resistor in position R1 and replace with 330R resistor.
    Remove existing 120K resistor in position R6 and replace with 22K resistor.
    Retune modulator sound core.


MK3 PSU and PIGGY BACK CPU

CPU:

    15K resistor (Brown, Green and Orange) from Pin 4 IC10 to Pin 10 IC12 (Sony Mod.)
    220N capacitor in position C3
    Cut resistor R6 and solder single cone wire to cut end, then solder other end of wire to pin 14 IC11.
    150 OHM resistor (Brownm Green and Brown) short circuited over R9.
    Drill back of board to open circuit track.

PSU:

    Remove existing 1.2K resistor in position R1 and replace with 330R resistor.
    Remove existing 120K resistor in position R6 and replace with 22K resistor.
    Retune modulator sound core.
  


MK3 PSU and SIEMENS CPU

CPU:

    15K resistor (Brown, Green and Orange) from Pin 4 IC10 to IC12 PIN 10 (Sony Mod.) or for neatness resistor may be fitted from C28 negative side to solder plate on IC12 Pin 10 line.
    220 OHM resistor short circuited over R9.
    6.8K resistor (Blue, Grey and Red) from bottom of R6 to solder plate near positive side of C28. This resistor needs to be sleeved.

PSU:

    Remove existing 1.2K or 68R resistor in position R1 and replace with 330R resistor.
    Remove existing 120K resistor in position R6 and replace with 22K resistor.
    Retune modulator sound core.