More Oojamaflips ready

For the discussion of all hardware related topics.
Post Reply
dublevay
Posts: 173
Joined: Wed Jan 23, 2019 3:41 pm

More Oojamaflips ready

Post by dublevay »

Guys,

Sorry, I have been neglecting to post here of late, but just wanted to let you know that a few more Oojamaflips are available. These are the internal boards which extend the cartridge port, giving one inside (but upside down) port, and retaining an external port.

Boards and components only supplied. Self build. Fixings into Dragons of the boards and/or accessories are the end user's responsibility.

Full details here: https://www.dragonplus-electronics.co.u ... it-version

N.B. not functionally compatible with Coco 1 due to -12V being present on Coco 1 cartridge port.
N.B. not guaranteed (or indeed even expected) to physically fit into Coco 2 & 3 cases.

Cheers

John
User avatar
robcfg
Posts: 1529
Joined: Sat Apr 04, 2009 10:16 pm
Location: Stockholm, Sweden
Contact:

Re: More Oojamaflips ready

Post by robcfg »

I think I may be ordering one, as having the CoCoPSG internally and a disk controller or the DragonMMC on the side, makes it a nice dev station.
dublevay
Posts: 173
Joined: Wed Jan 23, 2019 3:41 pm

Re: More Oojamaflips ready

Post by dublevay »

robcfg wrote: Thu May 14, 2020 3:09 pm I think I may be ordering one, as having the CoCoPSG internally and a disk controller or the DragonMMC on the side, makes it a nice dev station.
Thanks Rob... All boxed up and ready to leave here tomorrow.

John
User avatar
robcfg
Posts: 1529
Joined: Sat Apr 04, 2009 10:16 pm
Location: Stockholm, Sweden
Contact:

Re: More Oojamaflips ready

Post by robcfg »

Thank you very much!
pser1
Posts: 1655
Joined: Sun Mar 25, 2012 7:32 pm
Location: Barcelona (SPAIN)

Re: More Oojamaflips ready

Post by pser1 »

Hello John,
you pack with the oojamaflip has just arrived safely, thanks a lot!

Not in a hurry to build it immediately, because I am using
mini-MPI from Ed Snider or a standard Tandy multi-Pack when
I do need more than two cartridges ...

cheers
pere
User avatar
robcfg
Posts: 1529
Joined: Sat Apr 04, 2009 10:16 pm
Location: Stockholm, Sweden
Contact:

Re: More Oojamaflips ready

Post by robcfg »

Hi John,

The postman just dropped my Oojamaflip, looking forward to build and test it!
User avatar
robcfg
Posts: 1529
Joined: Sat Apr 04, 2009 10:16 pm
Location: Stockholm, Sweden
Contact:

Re: More Oojamaflips ready

Post by robcfg »

So, here's my beautiful finished Oojamaflip:
Oojama_robcfg.jpg
Oojama_robcfg.jpg (81.9 KiB) Viewed 6878 times
It works pretty well, and I'm most proud of how well the male edge connector turned out.

Fits well inside the case too.

Thanks John!
dublevay
Posts: 173
Joined: Wed Jan 23, 2019 3:41 pm

Re: More Oojamaflips ready

Post by dublevay »

Thanks for letting me know Rob. It looks great. Although I think you may have the fingers upside down, as I can see "39" where pin 2 is. It won't affect usability at all though.

Hope you find it useful.

Cheers.

John
Post Reply